Difference between revisions of "Red Neck Pic24 programmer"
From DiyLightAnimation
Steve Gase (Talk | contribs) |
|||
| Line 3: | Line 3: | ||
Since the pic used in the LE and Wireless boards needs different requirements. Here is a quick and simple way to do it without using a Lynx pcb that uses that pic. | Since the pic used in the LE and Wireless boards needs different requirements. Here is a quick and simple way to do it without using a Lynx pcb that uses that pic. | ||
| − | '''Note | + | '''Note: this is NOT for the PIC18F's for Freestyle, MR16, SSR with DMX option, or the USB Dongle.''' |
| + | |||
| + | '''Note: this method can ALSO be used for the Zeus and SSCv4 PIC24F04KA200 PIC programming. Use the table at the bottom of the page for the specialized pin-outs. | ||
| Line 11: | Line 13: | ||
[[Image:Pic24F-Pickit2.jpg]] | [[Image:Pic24F-Pickit2.jpg]] | ||
| + | |||
| + | |||
| + | {|cellpadding="5" cellspacing="0" border="1" | ||
| + | |+'''Wire Jumpers Needed for J1SYS/Redneck Board and PIC24FJ32GA002''' | ||
| + | |- | ||
| + | |'''PIC Chip Pin''' | ||
| + | |'''ICSP Header Pin''' | ||
| + | |- | ||
| + | |1 | ||
| + | |1 | ||
| + | |- | ||
| + | |28 | ||
| + | |2 | ||
| + | |- | ||
| + | |27 | ||
| + | |3 | ||
| + | |- | ||
| + | |4 | ||
| + | |4 | ||
| + | |- | ||
| + | |5 | ||
| + | |5 | ||
| + | |- | ||
| + | |not connected | ||
| + | |6 | ||
| + | |- | ||
| + | |} | ||
| + | |||
| + | {|cellpadding="5" cellspacing="0" border="1" | ||
| + | |+'''Wire Jumpers Needed for J1SYS/Redneck Board and PIC24F04KA200''' | ||
| + | |- | ||
| + | |'''PIC Chip Pin''' | ||
| + | |'''ICSP Header Pin''' | ||
| + | |- | ||
| + | |1 | ||
| + | |1 | ||
| + | |- | ||
| + | |14 | ||
| + | |2 | ||
| + | |- | ||
| + | |13 | ||
| + | |3 | ||
| + | |- | ||
| + | |3 | ||
| + | |4 | ||
| + | |- | ||
| + | |2 | ||
| + | |5 | ||
| + | |- | ||
| + | |not connected | ||
| + | |6 | ||
| + | |- | ||
| + | |} | ||
Latest revision as of 03:13, 24 November 2013
Bare bones pic24 series programmer interface
Since the pic used in the LE and Wireless boards needs different requirements. Here is a quick and simple way to do it without using a Lynx pcb that uses that pic.
Note: this is NOT for the PIC18F's for Freestyle, MR16, SSR with DMX option, or the USB Dongle.
Note: this method can ALSO be used for the Zeus and SSCv4 PIC24F04KA200 PIC programming. Use the table at the bottom of the page for the specialized pin-outs.
| PIC Chip Pin | ICSP Header Pin |
| 1 | 1 |
| 28 | 2 |
| 27 | 3 |
| 4 | 4 |
| 5 | 5 |
| not connected | 6 |
| PIC Chip Pin | ICSP Header Pin |
| 1 | 1 |
| 14 | 2 |
| 13 | 3 |
| 3 | 4 |
| 2 | 5 |
| not connected | 6 |
